Expert Answers about Dutchmen Voltage 5W Toy Hauler
- Reese Goose Box Gooseneck Adapter Fitment For a 2018 Dutchmen Voltage 3605 5TH Wheel Toy Hauler
- Your 2018 Dutchmen Voltage 3605 5TH wheel toy hauler has the mounting bolt pattern for a 1621HD Pin Box # LC1191151.
You need the Reese Goose Box # RP85FR to allow you to use your gooseneck ball to tow your Voltage. The maximum GVWR is 20,000lbs with a maximum tongue weight of 4,000lbs. Your Voltage has a GVWR of 16,800lbs and a dry tongue weight of 3,052lbs so you are safe within the limits.
Be sure to get a Reese Safety Chain Kit # RP49151 as you will be using a ball connection that...
view full answer... - Troubleshooting An RV Fireplace That Blinks And Won't Heat
- To fully reset the Furrion RV Electric Fireplace # FF30SC15ABL you'll want to remove the unit from the wall and unplug it from the wall outlet for about 15 mins. There could be enough residual power in the line to keep the circuit board in the fireplace powered for a bit even though you shut off the breaker. Once it's fully reset you'll want to ensure nothing is close enough to set the proximity sensor off again and can test the fireplace.
view full answer... - Which Trailair Rota-Flex 5th Wheel Pin Box Fits a 2013 Dutchmen Voltage V3105
- Thank you very much for all the information. I was able to use this and determine that you have a Lippert 1621HD pin box. Therefore the correct replacement for your 2013 Dutchmen Voltage V3105 is the Trailair Rota-Flex 5th Wheel Pin Box part # LC328330.
There will not be any issues using the Trailair Rota-Flex 5th Wheel Pin Box with your B&W Patriot 5th Wheel Trailer Hitch w/ Slider part # BWRVK3270.
view full answer... - Swapping to Larger 9/16 Wheel Studs On a 2017 Dutchmen Voltage 4005 5TH Wheel Toy Hauler
- Your Lippert Axle uses 1/2"-20X1.99" studs that have a 0.617 knurl for seating in the hub. I can recommend you a replacement hub assembly that does have the 9/16" studs, as I cannot locate any 9/16"-18 studs that have the same knurl dimensions.
The etrailer Trailer Hub and Drum Assembly # AKHD-865-7-1-K come preloaded with the 9/16" studs, lug nuts, new races, and bearings as well as a grease seal. This will also save you the time of having to press out and in all the wheel studs on your...
view full answer... - Replacing Ultra-Fab Landing Gear With Lippert Landing Gear With High-Powered Motor
- Thanks for all that good info, and what you have is the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010, which you can replace with a Lippert set with a high speed motor on you RV, though you will need to have new brackets welded on. The issue is that the Ultra-Fab has an uncommon 20-1/4 inch space between the mounting brackets, while Lippert and most others have landing gear with the standard 17-1/2 inches.
So if you were okay with having new brackets welded on to meet the spacing...
view full answer... - Fitment of the Lippert Electric Landing Gear Set on a 2011 Dutchmen Voltage V3200
- We do have a way to figure out if these are the correct fit for your 2011 Dutchmen Voltage V3200, but unfortunately I am not going to be able to say they are the same as OEM. I looked up the information for your Voltage and it just gives generic information regarding the jacks (which is normal). To determine if the Lippert Electric Landing Gear Set # LC333964 is the correct fit you will need to take a couple measurements. The measurements you are looking for are the length of the outer...
view full answer... - Replacement 29-1/2 Inch Landing Gear Legs for Venture Landing Gear
- We do have the correct 29-1/2 inch replacement legs for Venture landing gear, which is the following:
- Replacement Lead Jack with Drop Leg # LG-179013
- Replacement Follow Jack with Drop Leg # LG-179014
view full answer... - Will the Replacement Front Cover for Lippert Edge Awnings Work W/ My 2014 Dutchman Voltage 5W?
- The Replacement Front Cover for Lippert Edge Awnings # LC32NJ is meant to fit all of the Lippert Edge Awnings, so if you have a Lippert Edge awning on your 2014 Dutchmen Voltage, then this'll work just fine.
However if you don't have this awning, then it's not going to work. Since we don't know what you have on your trailer, you'll need to let us know what awning you have if it's not a Lippert Edge, and we'd be happy to find you the correct replacement front cover.
view full answer... - Can Curt 4 Bike Platform Rack be Used on 5th Wheel Toy Hauler
- For your application I recommend going with the Thule Range 4 Bike RV Rack # TH9057. The Curt 4 Bike Platform Rack # C18087 will technically fit, but Curt hasn't approved this rack for use on a towable trailer like your 5th wheel toy hauler like Thule has with the Range. This is due to the extra movement found at the hitch receiver on towable trailers.
If any of your bikes lacks the horizontal top tube that you find on a standard men's bike you'll need to utilize an adapter bar like part...
view full answer... - Camco Aluminum vs. Magnesium Hot Water Anode Rod
- The difference is aluminum hot water anode rods do not corrode as fast as magnesium because aluminum corrodes slower. Between the Camco hot water anode rods we carry, there is a size difference in the diameter, and the correct one depends on the hot water heater you have:
- 10-gallon Atwood: Camco RV Water Heater Anode Rod - Magnesium - 1/2" Diameter x 9-1/2" Long # CAM11593
- Suburban (Mor-Flo): Camco RV Water Heater Anode Rod - Aluminum - 3/4" Diameter x 9-1/2" Long # CAM11563
view full answer... - Lift Kit for a Triple Axle 2021 Dutchmen Voltage Toy Hauler
- There are a couple of options to lift your 2021 Dutchmen Voltage depending on if your axle's sit above or below the leaf springs. Either will have the capacity to support the weight of your trailer.
Most likely your axles are already below your leaf springs, which means the only option is the Correct Track Trailer Alignment and Lift Kit item # RR55QX for triple axle trailers. This kit mounts to your spring hangers and moves the attachment point down 1-1/4" or 2-1/4".
If your springs...
view full answer... - Replacement Pin Box For Gooseneck Connection On a Dutchmen Voltage 4225 Toy Hauler
- Yes, the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box # GY66FR is the correct weight capacity and bolt pattern for your 2021 Dutchmen Voltage 4225 5th Wheel Toy Hauler. It uses the same 1621HD bolt pattern as the Lippert Trailair Rota-Flex Pin Box # LC328329 that comes on your Voltage.
The Gen-Y is rated for a tongue weight of 3,500-5,500lbs and your dry tongue weight is 3,685lbs. The maximum trailer weight is 25,000lbs and your Voltage is rated to 20,000lbs.
You might...
view full answer...
Go To Results